Shipping in Canada

PuraSpa BP-2001 Spa Control System (Dedicated Circ Pump Required)

PuraSpa BP-2001 Spa Control System (Dedicated Circ Pump Required)

  • Includes Balboa TP600 Topside Control Panel.
  • PuraSpa BP-2001-CIRC Control System, Balboa Series.
CAD $899.99
- Main Power
- Circ Pump Circuit
- 2 Speed Pump Circuit
- Pump 2 / Blower Circuit
- Ozone Circuit
- Audio/Video Circuit
- WiFi

  • Product Description
  • Send to Friend

BalboaTM BP Series Platform Wi-Fi Enabled (with the addition of a Balboa Wi-Fi Module Kit).

This system will operate:

  • **Circulation Pump Circuit - 110V or 220V (a dedicated circulation pump is required to run this system)
  • Main Pump Circuit (2-Speed) - 110V or 220V
  • Pump 2 or Blower Circuit (1-Speed) - 110V or 220V
  • Ozonator Circuit - 110V or 220V (Must match voltage of circulation pump circuit below. If you do not have a small circulation pump, you have the option to set this circuit to either voltage. If you have a small circulation pump, you must use an ozonator with the same voltage as your circulation pump.)
  • Light Circuit - 12 Volts
  • Audio/Video Circuit - 110V or 220V
  • Will connect to a Balboa Wi-Fi Module Kit

**A dedicated circulation pump should not be confused with larger pump that powers your main jets. A dedicated circulation pump is commonly on 24 hours a day, only runs at a low RPM setting and is a little smaller than the pump that powers your main jets. For this system, the flow rate of your circulation pump must be at least 25 gallons per minute. In other words, the circulation pump must be similar to a Waterway Iron Might or Aquaflo Circmaster Pump and require a minimum 1.5" size plumbing. Pumps like the Waterway Tiny Might or Laing E10 Circulation Pump are too small and will not work with this control system.

Only PuraSpa control systems have all these features:

  • Long life Titanium 5.5 kW heater elements.

  • Color coded cords that plug-in on the outside of the spa pack. This eliminates the confusion of where to plug components in (other new systems on the market force you to turn the power off, slide the cord through the side of the box, consult a wiring diagram and then plug directly into the board). Our system is much easier and eliminates costly mistakes.

  • 'Heater On' Indicator Light - When lit, the heater element is getting voltage. This is very helpful when troubleshooting set-up issues and helps to identify faulty parts. 

  • BalboaTM M7 technology to prevent the heater from operating without proper water flow (eliminates troublesome pressure switches).

  • Proven BalboaTM BP circuit boards and topside controls.

  • PuraSpa® control systems are engineered for easy installation and convertible for all voltage configurations. This spa pack can be wired to 110 Volts or 220 Volts. If you wire to 220 Volts for the main power supply, all component circuits can be configured for 110 Volts or 220 Volts.

More than just standard features:

Balboa TP600 Topside included.

  • Balboa TP600 Top-side Control included (measures 7.1" X 3.5"). You can set the duration and number of daily filtration cycles. Digital temperature and functions read-out. Includes adapter plate for use if you currently have a larger top-side control.

  • Solid state electronic components and circuitry, for increased reliability and accurate temperature settings.

  • Universal features - main power convertible for either 110V or 220V service supply.

  • Universal 2-speed pump circuit - supports 110V or 220V (color coded 48" Cord included).

  • Universal 1-speed pump/blower circuit - supports 110V or 220V (color coded 48" Cord included).

  • Universal Ozonator circuit - supports 110V or 220V (color coded 48" Cord included).

  • Audio/Video circuit - supports 110V or 220V (when added, we include the male amp style cord).

  • Heater rated at 5.5 kW on 220 Volts or 1.4 kW on 110 Volts, in stainless steel heater manifold.

  • Full range solid state thermostat for precision accuracy.

  • 12V Light circuit with 96" cord.

  • Freeze protection mode - if a low temperature is sensed the pumps and blower will purge the system every two hours in addition to the set filtration cycles.

  • Heater ON indicator light.

  • Heater uses Balboa M7 internal dual sensors; for temperature control and high limit protection to prevent over-heating. These same dual sensors are also used to monitor water flow and prevent the heater from operating when flow is not adequate (eliminates the use of a trouble-some pressure switch).

  • Automatic time-out for light and pump.

  • Foot mounting brackets.

  • Compact design for easy installation - 15" heater housing (19.5" length to outside of white PVC unions), 11" height from floor to top, 3.5" depth.

  • UL, cUL and ETL recognized.

  • Wi-Fi Enabled (with the addition of a Balboa Wi-Fi Module Kit). You have the option of adding the Wi-Fi kit at a reduced price above or you can purchase later separately

Color Coded Component Cords

PuraSpa's cords are color coded, which makes plugging in your pump and other components failsafe. Our receptacles are located on the outside of the pack box, so there is no need to turn off the power, or open the electrical box to plug and unplug components.

Valuable items included:

  • Digital topside control with adapter plate (use the adapter plate if replacing a larger topside).
  • Color coded equipment cords.
  • Heater fittings with o-ring gaskets.
  • Installation and operation manual.

Universal Electrical Features Explained: Your spa pack will be factory configured to the voltage specifications you provide above. However, the main service and individual component voltages can be easily changed if your needs change in the future. If you do not have an ozonator, the voltage does not to be specified upon ordering. You will still receive the ozonator circuit so you have the option of adding one to your spa pack in the future. (Pumps and ozonators for the above system are sold separately. You are only selecting the voltage for these components when adding the pack to your shopping cart.)

Note: This control system must be hooked up to a GFCI protected line.

Backed by a 2 year manufacturer's warranty on all parts.

Send to Friend

Your name
Your email
Recipient's email
Add a personal message